i spec. no. ed-94054d sw 1 issue junel4, 1996 electronic components group sharp corporation specification device specification for business dealing name photocoupler model no. pc817 1. these specification sheets include materials protected under copyright of sharp corporation (?sharp?). please do not reproduce or cause anyone to reproduce them without sharp?s consent. 2. when using this product, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets, as well as the precautions mentioned below. sharp assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets, and the precautions mentioned below. (precautions) (1) this product is designed for use in the following application areas : [ * oa equipment * audio visual equipment * home appliances * telecommunication equipment (terminal) * measuring equipment * tooling machines * computers 1 if the use of the product in the above application areas is for equipment listed in paragraphs (21 or (31. please be sure to observe the precautions given in those respective paragraphs. (21 appropriate measures, such as fail-safe design and redundant design considering the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and safety in function and precision, such as : [ * transportation control and safety equipment (aircraft, train, automobile etc.) * traffic signals * gas leakage sensor breakers * rescue and security equipment * other safety equipment 1 (31 please do not use this product for equipment which require extremely high reliability and safety in function and precision. such as : [ * space equipment * telecommunication equipment (for trunk lines) * nuclear power control equipment * medical equipment ,i (41 please contact and consult with a sharp sales representative if there are any questions regarding interpretation of the above three paragraphs. 3. please contact and consult with a sharp sales representative for any questions about this product. customer?s approval date presented ?i by l/ date t. matsumura, department general manager of engineering dept.,11 by opto-electronic devices div. elecom group sharp corporation
sharp corpomition ed-94054d 1 june 14, 1996 model no. page pc8 17x l/8 1. application this speciiication applies to the outline and characteristics of photocoupler model-no. pc8 17series. refer to the attached drawing no. cy696 lk02. 2. outline 3. ratings and characteristics refer to the attached sheet, page 3 to 6. 4. reliability refer to the attached sheet, page 7. 5. incoming inspection refer to the attached sheet, page 8. 6. supplement 6.1 isolation voltage shall be measured in the following method. (1) short between anode to cathode on the primary side and between collector to emitter on the secondary side. (2) the dielectric withstand tester with zero-cross circuit shall be used. (31 the wave form of applied voltage shall be a sine wave. (it is recommended that the isolation voltage be measured in insulation oil.)
shflrp corporation ed-94054d 1 june 14. 1996 i model no. pc817x pag e 2/b 6.2 business dealing name (,, 0? mark indicates business dealing name of ordered product) 6.3 this model is approved by ul. approved model no. : pc8 17? ul file no. : e64380 6.4 this product is not designed against irradiation. this product is assembled with electrical input and output. this product incorporates non-coherent light emitting diode. 7. notes refer to the attached sheet- 1 - 1, 2. test conditions if=5ma ta=25c
sharp corporation ed-94054d 1 june 14, 1996 model no. page pc8 17x 3/8 3. ratings and characteristics 3.1 absolute maximum ratings ta=25% collector current * 1 collector power dissipation pc 150 mw * 1 total power dissipation ptot 200 mw *3 isolation voltage vii0 5 kvrms operating temperature topr -30 to +loo ?c storage temperature tstg -55 to +125 ?c *4 soldering temperature tsol 260 ?c *l the derating factors of absolute maximum ratings due to ambient temperature are shown in fig. 1 to 4. *2 pulse widths100 /is, duty ratio : 0.001 (refer to fig. 5) *3 ac for 1 min. 40 to 6o%rh *4 for 10s
sharp corporation ed-94054d 1 june 14. 1996 model no. page pc8 17x 4/b 3.2 electra-optical characteristics ta=25?c peak forward volta dark current e eo v,,=2ov, i,-0 - - 100 na collector-emitter bvceo ic=o. 1ma 35 - - v output breakdown voltage i,=0 emitter-collector bveco i,=10 pa, i,=0 6 - - v breakdown voltage collector current ic if=5ma, v,,=5v 2.5 - 30 ma collector-emitter v cebat) 1,=2oma 0.1 0.2 v saturation voltage ic=lma isolation resistance r is0 dc500v 5xlo?o 10? - r transfer 40 to 6o%rh charac- teristics floating capacitance c-f v=o, f=lmhz 0.6 1.0 pf cut-off frequency fc v,,=5v, ic=2ma - 80 - kj3z r,=loo r, -3db rise time fall time tr v,,=2v 4 18 /is ic=2ma tf r,=loo n 3 18 ps
ed-94054d 1 june 14, 1996 model no. page pc8 17x 5/8 sharp corporation rank mark anode mark factory identification m cu d d &g 34 d 1, \ !, / mark l 2 m 4 3 pin nos. and internal connection diagram k 7. 62?0.3 ? *11 2-digit number shall be marked according to din standard. unit: l/l mm *2) factory identification mark shall be or shall not be marked. i i *3) marking is laser marking pc817 name outline dimensions (business dealing name : pc8 17x1 i drawing hh i cy696 1 k02
shfirp corporation i ed-94054d 1 june 14. 1996 page 6/8 model no. pc817x (fig. 1) forward current vs. ambient temperature 0 -30 0 25 55 75 100 125 ambient temperature ta ( ?c ) (fig. 3) collector power dissipation t vs. ambient temperature -30 0 25 50 75 100 125 ambient temperature ta ( ?c ) (fig. 2) diode power dissipation vs. ambient temperature t i i i i 3 100 a 80 z 70 ,a 60 p 40 25 125 ambient temperature ta (?c i (fig. 4) total power dissipation vs. ambient temperature -30 0 25 50 75 100 125 ambient temperature ta (?c ) (fig. 5) peak forward current vs. duty ratio pulse widths100 ps ta=25?c duty ratio
the reliability of products shall be satisfied with items iisted below. coni?dence level : 90% ltpd: 10%/20% 4. reliability shflrp corporfition ed-94054d 1 june 14, 1996 model no. page pc817x 7/8 test items solderability *2 soldering heat terminai strength (tension) terminal strength (bending) *3 mechanical shock variable frequency vibration test conditions failure judgement samples b-i *1 criteria defeclive(c 230c. 5 s n=ll, c=o 260-c, 10 s n=ll, c=o weight : 5n n=ll, c=o 5 s/each terminal v,>ux 1.2 weight : 2.5n ia>uxz n=ll, c=o 2 times /each terminal 15000m/s2, 0.5ms eeo ?ijx2 n=ll, c=o 3 times/ tx, -ty, fz direction ic sharp corporation 5. incoming inspection 5.1 inspection items (11 electrical characteristics v,, i,, iceo, vcefsatl. ic, r,,. viso (21 appearance 5.2 sampling method and inspection level a single sampling plan, normal inspection level ii based on is0 2859 is applied. the aql according to the inspection items are shown below. defect inspection item major electrical characteristics defect unreadable marking minor appearance defect except defect the above mentioned. aql (%) 0.1 0.4 ed-94054d 1 june 14, 1996 model no. page pc817x 818
sharp corporation ed-94054d 1 june 14, 1996 model no. page pc817x attach sheet- i- 1 precautions for photocouplers 1 for cleaning (1) solvent cleaning : solvent temperature 45c or less immersion for 3 min or less (21 ultrasonic cleaning : the affect to device by ultrasonic cleaning is different by cleaning bath size, ultrasonic power output, cleaning time, pwb size or device mounting condition etc. please test it in actual using condition and con&-m that doesn?t occur any defect before starting the ultrasonic cleaning. applicable solvent : ethyl alcohol, methyl alcohol freon te v tf, diflon-solvent s3-e please refrain form using chloro fluoro carbon type solvent to clean device as much as possible since it is internationally restricted to protect the ozonosphere. before you use alternative solvent you are requested to con&-m that it does not attack package resin. 2. the led used in the photocoupier generally decreases the light emission power by operation. in case of long operation time, please design the circuit with considering the degradation of the light emission power of the led. (50%/5years)
sharp corporation ed-94054d 1 june 14. 1996 model no. page pc817x attach sheet- l-2 3. precautions for soldering photocouplers (1) in case of soldering an example of device temperature to lead vs. soldering time 260 ?c 10 s or less 130 - 160 - .*-- l-10 - *.-- _.-- 120 - *- .- .a device temperature i (?cl 0. ? ? ? ? ? ? ? ? ? 0 2 4 6 8 10 12 14 llj 18 20 soldering time (s) (2) if solder reflow : it is recommended thatonly one soldering be done at the temperature and the time within the temperature profile as shown in the figure. (3) other precautions an infrared lamp used to heat up for soldering may cause a localized temperature rise in the resin. so keep the package temperature within that specified in item (2). also avoid immersing the resin part in the solder.
|
